Mazda3 Forums banner

New Cobb Firmware Out - Includes DYNO functions

2K views 23 replies 12 participants last post by  AFcadet 
#1 ·
Also new cobb ap manager software out!
v1.3.2.0-8764
 
#6 ·
[quote author=aaronc7 link=topic=134933.msg2903206#msg2903206 date=1233444229]
FYI you need to enable 'beta" firmware downloads in the options in the AP updater program to get this right now
[/quote]

did u test ur car yet?? how much whp r u putting down aaronc7?
 
#7 ·
lol first run i had wheelspin in 3rd gear and it said i had something like 460whp lmao.

I did it again in 4th gear and it said 350. so yeah its reading high but then again this is BETA firmware and im not really sure what to put for weight of the car either
 
#14 ·
[quote author=aaronc7 link=topic=134933.msg2903381#msg2903381 date=1233452358]
lol first run i had wheelspin in 3rd gear and it said i had something like 460whp lmao.

I did it again in 4th gear and it said 350. so yeah its reading high but then again this is BETA firmware and im not really sure what to put for weight of the car either
[/quote]

when i've weighed at the track, the car was between 3200 and 3300lbs depending on how much fuel is in the car at the time, and whether or not the spare, jack, etc are in it. if you put in like 3800lbs, it would read way high, becaues it's thinking that the car is accellerating ~500lbs more than it actually is.
 
#15 ·
[quote author=Strizzo link=topic=134933.msg2908757#msg2908757 date=1233675030]
[quote author=aaronc7 link=topic=134933.msg2903381#msg2903381 date=1233452358]
lol first run i had wheelspin in 3rd gear and it said i had something like 460whp lmao.

I did it again in 4th gear and it said 350. so yeah its reading high but then again this is BETA firmware and im not really sure what to put for weight of the car either
[/quote]

when i've weighed at the track, the car was between 3200 and 3300lbs depending on how much fuel is in the car at the time, and whether or not the spare, jack, etc are in it. if you put in like 3800lbs, it would read way high, becaues it's thinking that the car is accellerating ~500lbs more than it actually is.
[/quote]

was that with you in it?
 
#17 ·
Well,
Last night my dyno was
355.2hp and 370.6ft lbs - 3300lbs; in 3rd gear; rpm start at 3000; rpm end at 6500
356.6hp and 368.4ft lbs - 3300lbs; in 3rd gear; rpm start at 3000; rpm end at 6500
660.1hp and 800.xft lbs - 3300lbs; in 4th gear; rpm start at 3000; rpm end at 6500 (cause I was going on/off boost/throttle on purpose just to see how outrageous the numbers would go

Oh no wheel spin, with TSC and DSC on.
 
#19 ·
Very interesting...

My numbers for two runs.

Both runs done at 3,300 lbs...3rd gear...3500rpm-6000rpm

1. 350 hp 417 ft/lb
2. 359 hp 416 ft/lb

I'm curious to why my tq is SO much higher then everyone elses lol...lighter wheels?

mods in sig
 
#20 ·
Has anyone else experiences problems after updating to this beta?

I got the accessport and immediately updated to the beta. When I tried to datalog tho, it wouldn't do it.
 
#22 ·
3300 lbs, 3rd gear, 3,500-6,000

Little bit warmer today (45 f), and I kno my car performs better above 40 degrees then below 40 degrees.

 
#24 ·
well no shit its not accurate lol.

But if we all put in 3300lbs...we can theoretically compar power.

And you can redo the tests after a mod and see if you theroeticaly added power
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top