[Kawwikid]

Ok, here they are, as promissed..I went to the Dyno this morning..The place is called Areocomp Racing, and its in Sanford, Fl..Great shop!!! Very nicely kept and very relaxed, but professional. They have a Dyno Jet 224 for FWD and RWD and a Mustang Dyno for AWD..These dyno runs where of course done on the Dyno Jet...I brain farted earlier when I said that I had gotten 272hp to the wheels the best run was 269.09, sorry, shoot me..LOL..The worst was 267.19 to the wheels. As for torque, the best was 290.53ftlbs to the wheels and the worst was 284.23ftlbs to the wheels...Not to shabby..All three runs where done with a 5 to 8 min window. There was a very nice cooling fan blowing on the TMIC, and there was minimal heat soak loss, so the ETS 3.5" TMIC is doing its job in a big way..My car had stock dyno runs from 228hp to 232hp wheel hp, and stock torque of 256ftlbs and 258ftlbs..So, you can judge the gains that it made by that..The only hp gaining mods that are done right now are CP-E CAI, ETS 3.5" TMIC and the Turbo XS race pipe...Thats all..You can also see from the graph that im running a bit on the lean side now, until 6K where it fell back to 11.5 to 1, kind of odd, but not to lean..I seriously cant wait until I get the CP-E programmer or Cobbs A/P to really dial the rest of this car in..I think and the techs as Areocomp think theres a least 40 to 50 more hp with a DP and a programer...We will see....for now, enjoy and I hope this helps.

By the way, the last run was done with the DSC and traction control off. The first two where done with just the DSC off...

 

[Kawwikid]

The same dyno type (dyno jet 224) diffearant place...As for the pulls they where all done in 4th gear...

 

[Kawwikid]

Im going to have to re-scan them again, sorry about that....let me see if I can get this right...

 

[Kawwikid]

Ok, while my wife trys to get the scanner working again for me..Heres what the dyno graph says, correction fact..is un-corrected..Im at sea level, it was 73degrees this morning and 33% humidity and the smoothing is 5....

 

[Kawwikid]

Im going to have to dig though the storage bins for it, my wife tends to be a bit of a pack rat and lumps everything together in one big bin..I think the TMIC is also adding to the leaness of the A/F ratio..The techs at Areocomp said that at the moment its boarder line lean in the mids and after 4.5k it seems to richen back up some, where it really needs that extra fuel..You can see that in the curve for torque..where there is a bigger nit at 4.5k to 6k, so Im thinking when I have away to get more fuel into her, it should smooth that out more and pick up the mid range even more..Im sure the CP-E by its self didnt lean it a to much. The car has never throwen a CEL even with the currnet mods to it....

 

[Kawwikid]

They where $85 for the first hour and $60 for each hour there after. They will discount for part hour time..Its a bit higher than most, but the way the shop looked and the care that they took when setting up the car was worth the extra money..

 

[Kawwikid]

Cosmic,
thanks for looking that info up about A/F and GDI motor. It makes me feel a little better about the A/F ratio that im getting right now..The only reason that I could think of that the TMIC might lean out the mixture a bit was that the increased air flow after the MAF senor, but im not sure about that. I had heard that the opt. A/F for a turbo car was 11.5 to 1, but that might have been with a normal fuel injection set-up..But for now she pulls hard, and spind the tire like no tommorw even with the DSC on, so it a fun place to be until more parts can be found. Im thinking Turbo XS down pipe and high-flow cat and the Cobb or CP-E programmer..Not to mention the Turbo Smart BOV.....Thanks everyone for you responses...

 

[Kawwikid]

I think thats the right name. Streetunit has a kit comming for the Speed 3 and Spped 6..Supposed to be a really nice BOV, that is very tunable and works in a neat Rec. and VTA mode...